Looking for:
Cisco air lap1142n manual |
Cisco Aironet 1142N manual.Cisco air lap1142n manual
Cisco air lap1142n manual.Cisco Aironet 1142 AIR-LAP1142N-S-K9 User Manual
Got to wireless Tab and click on it. Also make sure you are running a supported version on the WLC as the s are EOL and the last image they supported was 8.
Holding the mode button on this model of AP for more like seconds at power on did show different behaviour from the status light on it.
In this case it is because that model of AP is no longer supported by the firmware release 8. Salim's post suggests gave a 'not supported by firmware' message. Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:. Turn on suggestions. Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type. Showing results for. Search instead for.
Did you mean:. All Community This category This board. Start a conversation. I then attempt the manual reset using the steps from Cisco documentation: Step 1 - Disconnect power the power jack for external power or the Ethernet cable for in-line power from the access point. The status light does not turn amber. This is my problem. Attempts to connect to the device via Console cable or GUI have also failed. Any assistance appreciated. I have this problem too.
For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality.
Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language. Obtaining Documentation and Submitting a Service Request. Published: November 8, These mounting instructions describe the steps for mounting supported Cisco access points in several configurations, including on a suspended ceiling, on a hard ceiling or wall, on an electrical or network box, and above a suspended ceiling.
Mounting hardware for access points consists of brackets, which connect to the bottom of the access point, and ceiling grid clips, which attach the bracket to a suspended ceiling. The bracket you need depends on the mounting location for the access point. The ceiling grid clip that you need depends on the type of suspended ceiling where you need to install the access point.
You do not need ceiling grid clips if you mount the access point to a hard-surface ceiling or a wall. You use a ceiling grid clip to mount an access point on a suspended ceiling. The ceiling tiles or rails will determine which clip best works for the installation.
There are two types of ceiling grid clips:. For more details about the ceiling clips, see the Types of Ceiling Rails and Tiles section. Figure 3 shows a ceiling grid clip. The T-rail is the most common type of ceiling rail the supports for the ceiling tiles.
You can attach a ceiling grid clip directly to a T-rail ceiling rail. You need two adapter clips for each access point. Set screws on the clips and hold them securely on the ceiling rail. Figure 4 shows the three types of ceiling rails: T-rail, channel, and beam. Figure 5 shows an access point installed with a mounting bracket, ceiling grid clip, and adapter clips. Figure 4 Ceiling Rails and Tiles. Follow these steps to mount the access point below a standard or recessed, suspended ceiling.
Figure 6 shows an access point mounted on a T-rail ceiling rail using a ceiling grid clip. Figure 6 Suspended Ceiling Mounting Details. Follow these steps to mount the access point below a suspended ceiling. Step 1 Decide where you want to mount the access point on your suspended ceiling. Step 2 Open the ceiling grid clip completely. Step 3 Place the ceiling grid clip over the T-rail and close it to the appropriate detent A, B, or C. Step 4 Use a screwdriver to tighten the two ceiling grid clip locking screws to prevent the clip from sliding along the T-rail.
Step 5 Observe the ceiling grid clip width detent letter A, B, or C corresponding to the T-rail width. Step 6 Align the corresponding holes A, B, or C on the mounting bracket over the mounting holes on the ceiling grid clip. Step 8 If necessary, drill or cut a cable access hole in the ceiling tile large enough for the Ethernet and power cables. Pull the cables through the access hole until about 9 inches of cable protrude from the hole. Step 9 Connect the Ethernet and power cables to the access point.
Step 10 Align the access point feet over the keyhole mounting slots on the mounting bracket. If you created a hole for the cables, ensure the access point is positioned so the cables reach their respective ports. Step 11 Gently slide the access point onto the mounting bracket until it clicks into place. Step 12 Optional In high vibration areas or areas the AP could be bumped secure the AP to the mounting bracket with a small lock or a tie similar to a zip tie. Note Access points with integrated antennas perform best when the access point is mounted on horizontal surfaces such as a ceiling.
Ceiling mounting is strongly recommended for advanced features such as voice, location, and rogue access point detection. However, for smaller areas such as conference rooms, kiosks, transportation environments, or hot-spot usage where data coverage is the primary concern, the unit may be wall-mounted using wall anchors or screws.
Follow these steps to mount the access point on a solid ceiling or wall. Step 1 Use the mounting bracket as a template to mark the locations of the mounting holes on the bracket. Figure 7 and Figure 8 show details of the mounting bracket. Figure 8 Universal Mounting Bracket Details. Step 2 Drill a pilot hole at the mounting hole locations you have marked. Note The pilot hole size varies according to the material and thickness you are fastening.
Cisco recommends that you test the material to determine the ideal hole size for your mounting application. Step 3 Optional Drill or cut a cable access hole near and below the location of the mounting bracket cable access opening large enough for the Ethernet cable and power cables.
Step 4 Pull approximately 9 inches of cable through the hole. Route the Ethernet and power cables through the bracket before you attach the bracket to the ceiling or wall.
Route the cables through the main cable access hole and then through the smaller access hole, as shown in Figure 9. Figure 9 Routing the Ethernet and Power Cables. Step 5 Position the mounting bracket mounting holes over the pilot holes. Step 6 Insert a fastener into each mounting hole and tighten it. Step 7 Connect the Ethernet and power cables to the access point. Step 8 Align the access point feet with the large part of the keyhole mounting slots on the mounting plate.
When positioned correctly, the cable access cover will fit inside the access point connector bay. Step 9 Gently slide the access point onto the mounting bracket keyhole slots until it clicks into place.
Follow these steps to mount an access point to a network box or electrical box. Step 3 Pull approximately 9 inches of Ethernet and power cable through the hole. Route the cables through the bracket before you attach the bracket to the ceiling.
Route the cables through the main cable access hole and then through the smaller access hole as shown in Figure 9. Step 4 Connect the Ethernet and power cables to the access point. Step 5 Align the access point feet over the keyhole mounting slots on the optional mounting bracket. Step 6 Slide the access point onto the mounting bracket until it clicks into place. Using third-party accessories not offered by Cisco , you can mount an access point above a suspended ceiling.
The box hanger should be oriented just above the top surface of a ceiling tile. If your ceiling uses particularly thick tiles, you might need to modify the tile to allow room for the access point or use a box hanger that allows you to adjust the height of the access point, such as the Cooper B-Line BA50A. Note Install access points above ceiling tiles only when mounting below the ceiling is not an option.
Mounting access points above the ceiling can interfere with advanced wireless LAN features that depend on uniform coverage, such as voice and location. Follow these steps to mount the access point above a suspended ceiling. Figure 10 shows the completed installation. Step 1 Remove a ceiling tile adjacent to the mounting location. Step 2 Fasten the access point mounting bracket to the box hanger using the clip or screws provided with the box hanger kit.
No comments:
Post a Comment